When your furnace blows cold air, the problem may be as simple as the unit warming up or as serious as a failed ignitor or cracked heat exchanger. Common causes include incorrect thermostat settings, a clogged filter that triggers an overheat shutdown, a tripped limit switch, or problems with the pilot light or ignition system. Check thermostat settings, replace the filter and ensure vents are open. If the problem persists, call a professional as more serious issues like a failed blower motor or cracked heat exchanger may be to blame.<\/p>\n
January is Barrie’s coldest month, with average lows dipping below -10\u00b0C. When your furnace blows cold air, the indoor temperature plummets quickly. Frozen pipes and unsafe living conditions can result if you don’t resolve the issue promptly. Knowing how to troubleshoot your furnace<\/a> empowers homeowners and helps them decide when to seek professional help.<\/p>\n Upon startup, furnaces go through a pre-heating cycle. The blower may run for a minute or two before hot air arrives. Wait two to five minutes to see if warm air begins flowing.<\/p>\n Ensure the thermostat is set to “heat” and the fan is on “auto.” If it’s on “on,” the blower runs continuously and may blow room-temperature air when burners are off. Replace thermostat batteries and verify the temperature setpoint.<\/p>\n A clogged filter restricts airflow, causing the furnace to overheat. The limit switch shuts off the burners while the blower continues to run to dissipate heat, resulting in cold air. Replace the filter and reset the system.<\/p>\n In older furnaces with standing pilots, a thermocouple failure can extinguish the flame. Newer furnaces use electronic ignitors that can crack or wear out. A failed pilot assembly costs $150-$450 to replace. Ignitor replacements range $100-$450.<\/p>\n High-efficiency furnaces create condensate. If the drain line freezes or clogs, a safety switch shuts down the burners. Clear the line and insulate it to prevent freezing.<\/p>\n Insufficient gas pressure due to a closed valve, gas leak or supply disruption will prevent heating. Never attempt to adjust gas valves yourself. Evacuate if you smell gas and call your utility.<\/p>\nDetailed causes and solutions<\/h2>\n
Warm-up period<\/h3>\n
Thermostat settings<\/h3>\n
Dirty air filter<\/h3>\n
Pilot or ignitor problems<\/h3>\n
Blocked condensate line<\/h3>\n
Gas supply issues<\/h3>\n
Repair cost table<\/h2>\n
| Cause<\/th>\n | Typical repair cost (CAD)<\/th>\n | Notes<\/th>\n<\/tr>\n<\/thead>\n |
|---|---|---|
| Thermostat replacement<\/td>\n | $190-$480<\/td>\n | For faulty thermostats<\/td>\n<\/tr>\n |
| Filter replacement or basic tune-up<\/td>\n | $100-$300<\/td>\n | Includes service call<\/td>\n<\/tr>\n |
| Pilot or thermocouple replacement<\/td>\n | $150-$450<\/td>\n | Older furnaces<\/td>\n<\/tr>\n |
| Ignitor replacement<\/td>\n | $100-$450<\/td>\n | Common in newer furnaces<\/td>\n<\/tr>\n |
| Limit switch replacement<\/td>\n | $100-$375<\/td>\n | Overheat protection<\/td>\n<\/tr>\n |
| Blower motor repair<\/td>\n | $300-$900<\/td>\n | Necessary if motor fails<\/td>\n<\/tr>\n |
| Heat exchanger repair or replacement<\/td>\n | $1,000-$3,000<\/td>\n | Consider replacement<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nCommon mistakes<\/h2>\nWhen to call a professional<\/h2>\nCall for professional furnace repair in Barrie<\/a> if you’ve checked thermostat settings, replaced the filter and waited through the warm-up period but still have cold air. Also call if you smell gas, hear unusual noises, see a blinking error code or notice water around the furnace. These symptoms may indicate a failed control board, cracked heat exchanger or gas leak problems that require expert diagnosis. If the heat exchanger is cracked on an aging system, a new high-efficiency furnace<\/a> is often the safer long-term choice.<\/p>\n Keeping your Barrie home warm during frigid January weather means acting fast when your furnace starts blowing cold air. Affordable Comfort’s technicians can pinpoint the cause and get your system heating again, often the same day, so you can avoid frozen pipes and enjoy a cozy winter.<\/p>\n","protected":false},"excerpt":{"rendered":" When your furnace blows cold air, the problem may be as simple as the unit warming up or as serious as a failed ignitor or cracked heat exchanger. Common causes include incorrect thermostat settings, a clogged filter that triggers an … Continue reading |